<dd id="jm78x"><center id="jm78x"><video id="jm78x"></video></center></dd>
<em id="jm78x"><acronym id="jm78x"><input id="jm78x"></input></acronym></em>
    1. <li id="jm78x"><acronym id="jm78x"></acronym></li>
      <th id="jm78x"></th>

        歡迎光臨濟南九創門業有限公司官網!

        聯系我們 收藏本站 在線留言

        新聞資訊

        首頁>>新聞資訊>>快速自動卷簾門出現故障時如何檢查?
        新聞資訊
        聯系我們
        濟南九創門業有限公司

        聯系人:李經理

        電話:15006519345

        網址:www.halc9bit.com

        地址:濟南市天橋區北園大街372號大明家居3F-A-10

        快速自動卷簾門出現故障時如何檢查?

        來源:http://www.jnhsjlm.com 日期:2022-03-02 發布人:guanli
        快速自動卷簾門出現故障時如何檢查?
        How to check when the fast automatic rolling shutter door fails?
        如何快速檢測快速自動卷簾門故障?
        How to quickly detect the fault of fast automatic rolling shutter door?
        目前,我國大、中、小企業普遍使用快門,其正常使用直接關系到企業的正常生產和工作。許多用戶在使用快門時都面臨著門體無法關閉的問題。因為不知道怎么處理,很多人都找過廠家的技術人員來處理。但是技術人員到達現場后,發現這只是一個小問題,用戶花錢浪費時間就不用處理了。為了避免快速自動快門用戶的時間和財力損失,我們將討論快速自動卷簾門的故障檢測方法。
        At present, the shutter is widely used in large, medium and small enterprises in China, and its normal use is directly related to the normal production and work of enterprises. Many users are faced with the problem that the door cannot be closed when using the shutter. Because I don't know how to deal with it, many people have asked the technicians of the manufacturer to deal with it. However, after the technicians arrived at the scene, they found that this was only a small problem, and users didn't have to deal with it if they spent money and wasted time. In order to avoid the loss of time and financial resources of fast automatic shutter users, we will discuss the fault detection method of fast automatic rolling shutter door.
        1、檢查接地感應線圈。如果地面感應控制器的綠燈長時間點亮,快速自動卷簾門的手動和自動開關將失效。操作時,您需要按住地面感應控制器的重啟按鈕5秒。關掉交通燈,紅燈長時間點亮,門可以關上。如果綠光長時間點亮,請檢查接地傳感器附近是否有鐵屑,清除鐵屑,門體恢復正常。
        1. Check the grounding induction coil. If the green light of the ground sensing controller is on for a long time, the manual and automatic switches of the fast automatic rolling shutter door will fail. During operation, you need to press and hold the restart button of the ground sensing controller for 5 seconds. Turn off the traffic lights, the red light will be on for a long time, and the door can be closed. If the green light is on for a long time, please check whether there are iron chips near the grounding sensor, remove the iron chips, and the door body returns to normal.
        2、檢查快速自動快門的紅外指示器。如果設置門自動延遲關閉時間,快速自動快門不能下降或關閉,紅外燈為紅色,指示紅外位置異常。需要調整紅外線位置,直到故障排除,綠燈亮起,門才能正常關閉。
        2. Check the infrared indicator of the fast automatic shutter. If the door automatic delay closing time is set, the fast automatic shutter cannot be lowered or closed, and the infrared light is red, indicating that the infrared position is abnormal. The infrared position needs to be adjusted until the fault is eliminated and the green light is on, so that the door can be closed normally.
        3、檢查快門吊索、快門等部件脫落,快門無法關閉。操作時,應逐一檢查和清除可疑零件,確認正常。
        3. Check that the shutter sling, shutter and other parts fall off and the shutter cannot be closed. During operation, check and remove suspicious parts one by one to confirm that they are normal.
        4、快速自動快門不能升降。原因:可能是電源故障、電機故障或門本身堵塞。措施:檢查主電源、控制電源和電機,檢查門。
        4. Fast automatic shutter cannot be raised or lowered. Cause: it may be power failure, motor failure or door blockage. Measures: check the main power supply, control power supply and motor, and check the door.
        5、防火快速自動快門不降不升。理由:上下按鈕,接觸器觸頭線圈、限位開關、接觸器鎖常閉觸點。操作步驟:檢查上下按鈕、下或上接觸器觸頭開關和線圈,檢查限位開關、底部或上接觸器的常閉觸點。
        5. Fire fast automatic shutter does not fall or rise. Reason: up and down buttons, contactor contact coil, limit switch, contactor lock normally closed contact. Operation steps: check the upper and lower buttons, lower or upper contactor contact switches and coils, and check the normally closed contacts of limit switches, bottom or upper contactors.
        6、控制無法連接快門。原因:控制本身的控制裝置故障、控制模塊故障和聯動輸送線故障。過程:檢查控制控制單元本身、控制模塊和傳輸線路。
        6. The control center cannot connect the shutter. Cause: control device failure, control module failure and linkage conveyor line failure of the control center itself. Process: check the control unit itself, control module and transmission line of the control center.
        以上就是今天帶給大家的知識,濟南卷簾門維修專注行業多年,為用戶不斷的提供有價值的內容,更多內容請繼續關注我們:http://www.halc9bit.com
        The above is the knowledge brought to you today. Jinan roller shutter door maintenance has focused on the industry for many years and continuously provides users with valuable content. Please continue to pay attention to us for more content: http://www.halc9bit.com

        推薦閱讀/ Recommended reading

        快速自動卷簾門出現故障時如何檢查? How to check when the fast automatic rolling shutter door fails? 如何快速檢測快速自動

        車庫門怎么調行程? 2022-02-26
        車庫門的五種常見故障及其排除方法 2022-02-24
        車庫門維修后如何進行日常維護? 2022-02-18
        日常清洗卷簾門的方法有哪些? 2022-02-18

        【本站圖片均由網站所有方提供,部分圖片來源于網絡,如無意中侵犯了某媒體或個人的知識產權,請來信或來電告之,本網站將立即刪除?!?/p>

        • 濟南九創門業有限公司
        乌克兰裸体美女AAAAAA片,久久精品人妻一区二区三区,女班长裸体扒开两腿让我桶动态图,欧美性爱A片