<sub id="a8h0n"><listing id="a8h0n"></listing></sub>
      <strike id="a8h0n"><pre id="a8h0n"></pre></strike>

      歡迎光臨濟南九創門業有限公司官網!

      聯系我們 收藏本站 在線留言

      新聞資訊

      首頁>>新聞資訊>>車庫門安裝好后如何調試
      新聞資訊
      聯系我們
      濟南九創門業有限公司

      聯系人:李經理

      電話:15006519345

      網址:www.halc9bit.com

      地址:濟南市天橋區北園大街372號大明家居3F-A-10

      車庫門安裝好后如何調試

      來源:http://www.jnhsjlm.com 日期:2021-11-15 發布人:guanli
      車庫門安裝完成后的調試過程
      Debugging process after garage door installation
      1,反彈力力量通過主板電位器選定。
      1. The rebound force is selected through the potentiometer of the main board.
      2,通電后主板對碼燈-開門燈-關門燈-照明燈閃3次后滅,此時即為侍機狀態。若主板狀態指示燈不亮,請檢查電源是否接通。
      濟南車庫門
      2. After power on, the motherboard alignment lamp - door opening lamp - door closing lamp - lamp flashes for 3 times and then goes out. At this time, it is in the waiting state. If the motherboard status indicator is not on, check whether the power is connected.
      3,****開門關門行程限位設定****(1)長按設置鍵一直到開門指示燈(綠燈)快閃6次變常亮狀態后松手(此時進入開門設置狀態)。
      3, * * * * door opening and closing stroke limit setting * * * * * * (1) long press the setting key until the door opening indicator (green light) flashes for 6 times and becomes normally on (enter the door opening setting state at this time).
      然后長按“開門”鍵不松手,門體上行到合適的位置后松手,這時再次長按設置鍵一直到開門燈(綠燈)快閃6次變為關門燈(藍燈)常亮后松手(此時進入關門設置狀態)。
      Then, long press the "open door" key and don't let go. When the door body rises to the appropriate position, release it. At this time, long press the setting key again until the door opening light (green light) flashes for 6 times and becomes the door closing light (blue light) is always on (enter the door closing setting state at this time).
      再長按:“關門”鍵不松手,門體下行到合適位置后松手。再次長按設置鍵一直到關門燈(藍燈)快閃6次后燈滅為止,設置完成。
      Press and hold the "close the door" key again, and then release the door when it moves down to the appropriate position. Press and hold the setting key again until the closing light (blue light) flashes for 6 times and the light goes out, and the setting is completed.
      (2)注意事項***初次使用必須設置行程,否則遙控器不能用***(4)以上設置簡易流程:設置-開門-設置-關門一設置-OK遙控器對碼、消碼1,消碼:按住對碼鍵五秒至指示燈熄滅,則消碼完成。
      (2) Precautions * * the travel must be set for the first use, otherwise the remote control cannot be used * * (4) the above simple process of setting: setting - opening door - setting - closing door - setting - OK remote control code matching and code cancellation 1. Code cancellation: press and hold the code matching key for five seconds until the indicator light goes out, and the code cancellation is completed.
      2,對碼:按住主板對碼鍵不松手,對碼燈“紅燈”常亮后松手,然后按2-4下逼控器上所需對碼的鍵(開鎖或關鎖),對碼指示燈由常亮變閃亮即可,注:學碼前必須先設行程,否則遙控器對碼后無任何反應
      2. Code matching: press and hold the code matching key on the motherboard and let go after the code matching light "red light" is always on, and then press 2-4 to force the required code matching key on the controller (unlock or close the lock), and the code matching indicator will change from normally on to flashing. Note: the travel must be set before learning the code, otherwise the remote control will not respond to the code
      濟南車庫門http://www.halc9bit.com感謝您的瀏覽,如有其他疑問歡迎登錄我們官網進行查看。
      Jinan garage door http://www.halc9bit.com Thank you for your browsing. If you have any other questions, please log in to our official website.

      推薦閱讀/ Recommended reading

      車庫門安裝完成后的調試過程Debugging process after garage door installation1,反彈力力量通過主板電位器選定。1 The rebound f

      防火卷簾門的選擇要求 2021-11-11
      車庫門關不上的原因與解決辦法 2021-11-09
      卷簾車庫門產品的特點以及使用優勢有哪些? 2021-11-02
      車庫門五金件的詳細介紹 2021-10-31

      【本站圖片均由網站所有方提供,部分圖片來源于網絡,如無意中侵犯了某媒體或個人的知識產權,請來信或來電告之,本網站將立即刪除?!?/p>

      • 濟南九創門業有限公司
      偏僻农村大乱纶,亚洲夜夜性无码国产盗摄,国产免费看福利,国自产拍偷拍福利精品,东方亚洲欧A∨人在线