<sub id="a8h0n"><listing id="a8h0n"></listing></sub>
      <strike id="a8h0n"><pre id="a8h0n"></pre></strike>

      歡迎光臨濟南九創門業有限公司官網!

      聯系我們 收藏本站 在線留言

      新聞資訊

      首頁>>新聞資訊>>車庫門的安裝應該注意哪些方法?
      新聞資訊
      聯系我們
      濟南九創門業有限公司

      聯系人:李經理

      電話:15006519345

      網址:www.halc9bit.com

      地址:濟南市天橋區北園大街372號大明家居3F-A-10

      車庫門的安裝應該注意哪些方法?

      來源:http://www.jnhsjlm.com 日期:2021-08-04 發布人:guanli
      安裝車庫門時較開始需要測量車庫門口上沿至棚頂的距離或折算出車庫門凹版上沿至棚頂的距離,較小距離不得少于250mm,以便安裝車庫門的中軸桿,一般要求距離300-400mm。 測量車庫門洞口的左右墻垛寬度,正常尺寸為120—150mm,較小不得小于70,一般情況下,用戶應準備60× 成都安裝維修車庫門的1 50mm×車庫門高度×3根的木方。檢查車庫門洞口、棚頂、洞口左右墻垛等處是否有障礙物。
      When installing the garage door, it is necessary to measure the distance from the upper edge of the garage door to the shed top or convert the distance from the upper edge of the garage door gravure to the shed top. The smaller distance shall not be less than 250mm, so as to install the middle shaft rod of the garage door. Generally, the distance is required to be 300-400mm. Measure the width of the left and right wall stacks of the garage door opening. The normal size is 120-150mm, and the smaller size shall not be less than 70. Generally, the user shall prepare 60 ×  50mm for installation and maintenance of garage door in Chengdu × Garage door height × 3 pieces of wood. Check whether there are obstacles at the garage door opening, shed roof, left and right wall stacks of the opening, etc.
      測量完成后就要立門框,門框的大小必須同門的大小一致,門框的立柱必須垂直,橫梁必須水平。隨后就是立門板,用螺釘將封條固定在門板底部:再固定底部托架,然后將1號合頁和2號合頁固定在靠前塊門板與第二塊門板連DOOYA打不開車庫門了接處和靠前塊門板上端按順序依此連接。
      濟南車庫門
      After the measurement, the door frame shall be erected. The size of the door frame must be consistent with the size of the door. The column of the door frame must be vertical and the beam must be horizontal. Then there is the vertical door panel. Fix the seal at the bottom of the door panel with screws: then fix the bottom bracket, and then fix the No. 1 hinge and No. 2 hinge at the connection between the front door panel and the second door panel. Dooya can't open the garage door, and connect the upper end of the front door panel in sequence.
      對于道軌連接的時候要將左、右直立道軌分別放在木框正面,分別將道軌軸輪放在道軌內,并與合頁孔連接好,用自攻螺釘把道軌固定在木框上,分別將滑道連接件固定在道軌上,然后測量該角鐵是否與木框成90°角,將左、右彎道軌分別于滑道連接件連接,要求彎道。
      When connecting the track, place the left and right vertical track on the front of the wooden frame respectively, place the track shaft wheel in the track and connect it with the hinge hole, fix the track on the wooden frame with self tapping screws, fix the slide connector on the track respectively, then measure whether the angle iron forms a 90 ° angle with the wooden frame, and connect the left and right bend rails to the slide connector respectively, Curve required.
      接下來就是扭矩彈簧的安裝,中軸桿一端套上軸套托架,按左右位置穿入扭矩彈簧,按左右位置穿入盤絲繩輪,將組裝女子的軸桿放在滑道連接件上,用螺釘固定在門頭木框上。安裝第四塊門的時候將門板與第三塊門板相連接,將兩側盤絲繩輪上的鋼絲與靠前塊門板掛連,給扭矩彈簧上緊(一般上緊8-9圈,視門體大小) 。
      The next step is the installation of the torque spring. One end of the middle shaft rod is sleeved with the shaft sleeve bracket, the torque spring is threaded in according to the left and right positions, and the wire reel is threaded in according to the left and right positions. The shaft rod assembled is placed on the slide connector and fixed on the wooden frame of the door head with screws. When installing the fourth door, connect the door panel with the third door panel, connect the steel wire on the wire rope sheaves on both sides with the door panel near the front, and tighten the torque spring (generally 8-9 turns, depending on the size of the door body).
      彎道軌的固定要用鋼卷尺測量彎道軌與頂棚的距離,按照測量尺寸截斷多孔角鐵,做成三角支架,分別將多孔三角支架固定在棚頂左右彎道軌的上方,并與彎道軌相連接。還應該連接應急緩衡桿,將緩衡桿短端與門板連接,長端與鏈條連接,調整緩衡桿的長短尺寸(一般要求緩衡桿與大連堆積門廠家鏈條固定端到門板的距離為250-300mm) 。
      The distance between the bend rail and the ceiling shall be measured with a steel tape for the fixation of the bend rail. The porous angle iron shall be cut off according to the measured size to make a triangular support. The porous triangular support shall be fixed above the left and right bend rails on the ceiling and connected with the bend rail. Connect the emergency balance rod, connect the short end of the balance rod with the door panel and the long end with the chain, and adjust the length of the balance rod (generally, the distance between the balance rod and the chain fixed end of Dalian Jimen manufacturer to the door panel is 250-300mm).
      以上的精彩內容來自: 濟南車庫門提供分享,更多的精彩內容請點擊進入我們的網站:http://www.halc9bit.com,我們會有更多的精彩內容等您查看
      The above wonderful content comes from Jinan garage door. For more wonderful content, please click to enter our website: http://www.halc9bit.com , we will have more wonderful content for you to see

      推薦閱讀/ Recommended reading

      1、導軌1 Guide rail翻板車庫門當中的導軌采用的是鍍鋅鋼板,鋼板的厚度為1 5mm,它是經過一次性的操作而成形的。The guide rail in

      選擇卷簾門時可以借鑒什么 2021-10-27
      透視車庫門有什么樣的優缺點? 2021-10-19
      現代化的車庫門在設計方面要注意什么? 2021-10-15
      防盜車庫門的選購應該注意什么? 2021-09-25

      【本站圖片均由網站所有方提供,部分圖片來源于網絡,如無意中侵犯了某媒體或個人的知識產權,請來信或來電告之,本網站將立即刪除?!?/p>

      • 濟南九創門業有限公司
      偏僻农村大乱纶,亚洲夜夜性无码国产盗摄,国产免费看福利,国自产拍偷拍福利精品,东方亚洲欧A∨人在线