<sub id="a8h0n"><listing id="a8h0n"></listing></sub>
      <strike id="a8h0n"><pre id="a8h0n"></pre></strike>

      歡迎光臨濟南九創門業有限公司官網!

      聯系我們 收藏本站 在線留言

      新聞資訊

      首頁>>新聞資訊>>車庫門定期保養需注意6點事項?
      新聞資訊
      聯系我們
      濟南九創門業有限公司

      聯系人:李經理

      電話:15006519345

      網址:www.halc9bit.com

      地址:濟南市天橋區北園大街372號大明家居3F-A-10

      車庫門定期保養需注意6點事項?

      來源:http://www.jnhsjlm.com 日期:2020-07-14 發布人:guanli
        1.檢查彈簧
        1. Check the spring
        在上掀門上,每一面的彈簧都掛在槽中。將彈簧鉤移至相鄰的槽中,調整其彈力。在卷簾門上,每一面的彈簧均由滑輪上的彈簧式纜線控制。為了調整彈簧的彈力,請將經過門上方平板的纜線拉長,然后在末端重新打結,以保持新的彈力。警告:如果卷簾門只在門有一個扭轉彈簧,請不要嘗試修理它。因為那彈簧的彈力實在是太大了,可能會使您受傷。對于使用了這種彈簧的門,應當打電話向維修服務部門求助
        On the liftgate, springs on each side hang in the slots. Move the spring hook to the adjacent slot and adjust its spring force. On the rolling shutter door, the spring on each side is controlled by the spring type cable on the pulley. In order to adjust the spring force, lengthen the cable passing through the flat plate above the door, and then tie the knot again at the end to maintain the new spring force. Warning: if a rolling shutter door has only one torsion spring in the center of the door, do not attempt to repair it. Because the spring is so strong that it may hurt you. For doors that use this spring, you should call a professional maintenance service department for help
        2.將所有變松的螺絲擰緊
        2. Tighten all loose screws
        請查找變松的部件,并根據需求上緊。在上掀門上,檢查安裝彈簧的平板,確保螺釘已經旋緊,并將變松的螺釘擰緊。在卷簾門上,請檢查將門的各個部分固定在一起的鉸鏈,將所有變松的螺釘擰緊,并更換受損的鉸鏈。門有時向一側下沉,這個問題往往可以通過維修鉸鏈來糾正。如果螺釘孔變大了,請換一根直徑相同但更長的螺釘,在一根空心纖維棒上涂木工膠,然后套在新螺釘上。如果鉸鏈處的木料出現裂縫,請拆掉鉸鏈,將木料填孔劑填在裂縫和螺釘孔中。待填孔劑干燥后再更換鉸鏈。如果可能,請將鉸鏈移到實心木料上。
        Please find the loose parts and tighten them as required. On the upper lift door, check the spring plate to make sure that the screws have been tightened and tighten the loosened screws. On roller shutter doors, check the hinges that hold the various parts of the door together, tighten all loose screws, and replace damaged hinges. Doors sometimes sink to one side, which can often be corrected by repairing the hinges. If the screw hole becomes larger, replace a screw with the same diameter but longer, coat a hollow fiber rod with wood glue, and then put it on the new screw. If there are cracks in the wood at the hinge, remove the hinge and fill the crack and screw hole with wood filler. Replace the hinge after the filling agent is dry. If possible, move the hinge to the solid wood.
                  濟南車庫門
        3.確保軌道是否在水平線上
        3. Make sure the track is on the horizontal line
        用水平儀檢查軌道,確保軌道在同一水平線上。水平軌道應當略向車庫后部傾斜,如果是卷簾門,軌道的縱向部分應精確垂直。在車庫的墻壁上,兩條軌道必須處于同一高度,如果軌道沒有準確對齊,請將固定安裝支架的螺釘或螺栓擰松,但不要把它們取下來,然后小心地敲打軌道,使它們移動到適當的位置。用水平儀重新檢查軌道,確保它們處于正確的位置,然后將安裝支架上的螺釘或螺栓擰緊。
        Check the track with a level to ensure that the track is on the same level. The horizontal track should be slightly inclined to the rear of the garage, and in the case of rolling shutter doors, the longitudinal part of the track should be exactly vertical. On the wall of the garage, the two rails must be at the same height. If the rails are not correctly aligned, loosen the screws or bolts that fix the mounting bracket, but do not remove them, and then carefully tap the rails to move them into place. Recheck the rails with a spirit level to make sure they are in the correct position, and then tighten the screws or bolts on the mounting bracket.
        4.檢查金屬軌道
        4. Check the metal track
        檢查車庫內部的金屬軌道,查看將軌道固定到墻壁的安裝支架。如果支架松了,請擰緊螺栓或螺釘。將車庫門關上,在車庫內部檢查軌道是否有凹陷、彎曲或變平的地方,如果有任何損壞之處,請用橡皮錘,或用一塊廢木料墊著錘子敲打這些地方。如果軌道嚴重損壞,您必須更換。
        Check the metal rails inside the garage to see the mounting brackets that hold the rails to the wall. If the bracket is loose, tighten the bolts or screws. Close the garage door and check the track inside the garage for dents, bends, or flattening. If there is any damage, tap these places with a rubber hammer or a piece of wood cushion. If the track is seriously damaged, you must replace it.
        5.在軌道上噴灑潤滑油
        5. Spray lubricating oil on the track
        將石墨粉撒在軌道上,將家用潤滑油或硅樹脂噴在轉軸上,或者在軌道和轉軸上噴灑車庫門專用潤滑油噴劑,以起到潤滑作用。如果有滑輪,請您使用和用在轉軸上的相同的潤滑劑潤滑。
        Sprinkle graphite powder on the track, spray household lubricating oil or silicone resin on the rotating shaft, or spray special lubricating oil spray for garage door on the track and shaft to play a lubricating role. If there are pulleys, please use the same lubricant as used on the shaft.
        6.將軌道污垢去除干凈
        6. Remove the track dirt
        用高濃度家用清潔劑清洗軌道,去除污垢和硬化的油脂。將轉軸徹底清洗干凈,然后將軌道和轉軸擦干。
        Clean the track with a high concentration of household cleaner to remove dirt and hardened grease. Clean the shaft thoroughly, then dry the track and shaft.

      推薦閱讀/ Recommended reading

      1、導軌1 Guide rail翻板車庫門當中的導軌采用的是鍍鋅鋼板,鋼板的厚度為1 5mm,它是經過一次性的操作而成形的。The guide rail in

      選擇卷簾門時可以借鑒什么 2021-10-27
      透視車庫門有什么樣的優缺點? 2021-10-19
      現代化的車庫門在設計方面要注意什么? 2021-10-15
      防盜車庫門的選購應該注意什么? 2021-09-25

      【本站圖片均由網站所有方提供,部分圖片來源于網絡,如無意中侵犯了某媒體或個人的知識產權,請來信或來電告之,本網站將立即刪除?!?/p>

      • 濟南九創門業有限公司
      偏僻农村大乱纶,亚洲夜夜性无码国产盗摄,国产免费看福利,国自产拍偷拍福利精品,东方亚洲欧A∨人在线