<dd id="jm78x"><center id="jm78x"><video id="jm78x"></video></center></dd>
<em id="jm78x"><acronym id="jm78x"><input id="jm78x"></input></acronym></em>
    1. <li id="jm78x"><acronym id="jm78x"></acronym></li>
      <th id="jm78x"></th>

        歡迎光臨濟南九創門業有限公司官網!

        聯系我們 收藏本站 在線留言

        新聞資訊

        首頁>>新聞資訊>>鋁合金卷簾門操作不當會出現哪些問題?
        新聞資訊
        聯系我們
        濟南九創門業有限公司

        聯系人:李經理

        電話:15006519345

        網址:www.halc9bit.com

        地址:濟南市天橋區北園大街372號大明家居3F-A-10

        鋁合金卷簾門操作不當會出現哪些問題?

        來源:http://www.jnhsjlm.com 日期:2020-05-13 發布人:admin
          濟南鋁合金卷簾門安裝后,如果操作不當,很可能會出現松動等問題。那么這個問題的原因是什么呢?下面濟南卷簾門廠一起來看看。
          After the installation of Jinan aluminum alloy roller shutter door, if the operation is improper, it is likely to loose. So what's the cause of this problem? Let's have a look at Jinan roller shutter factory.
          1、鋁合金卷簾門四周的鐵腳入墻太少或后澆砂漿碰撞。
          1. The iron feet around the aluminum alloy rolling shutter door are too few into the wall or the post pouring mortar collides.
          2. 卷簾門頂部的鐵腳沒有延伸到預留的孔內,或者門頂部的鐵腳沒有與嵌入在門楣上的鐵件牢固焊接。
          2. The iron feet on the top of the roller shutter door are not extended into the reserved holes, or the iron feet on the top of the door are not firmly welded with the iron parts embedded in the lintel.
          3.門的鐵腳沒有按照相關要求進行固定。
          3. The iron foot of the door is not fixed according to the relevant requirements.
          這就要求濟南相關人員在安裝鋁合金卷簾門時,要注意以下要求:
          This requires Jinan relevant personnel to pay attention to the following requirements when installing the aluminum alloy rolling shutter door:
          相鄰互鎖簾板經過系列靈活轉動,擺動±90度,不允許脫落。
          The adjacent interlocking curtain plate can rotate flexibly through a series of steps, swing ± 90 degrees, and it is not allowed to fall off.
          2、簾板兩端擋板或防竄機構要組裝牢固,組裝成一個卷簾,簾板竄動量不得大于2mm。
          2. The baffles at both ends of the curtain plate or the anti channeling mechanism shall be firmly assembled into a rolling curtain, and the channeling momentum of the curtain plate shall not be greater than 2mm.
          3、簾板要平直,簾板直線度不得大于1.5mm/m,全長直線度不得超過0.12%。
          3. The curtain plate shall be straight, and the straightness of the curtain plate shall not be more than 1.5m m/m, and the straightness of the whole length shall not be more than 0.12%.
          4、簾板組裝成百葉,不得有孔洞和縫隙。
          4. The curtain plate shall be assembled into louver without holes and gaps.
          5、卷簾板組裝成一個卷簾,在操作時不得有傾斜,應平行升降,卷簾的高度不大于口的1/300。
          5. The roller shutter plate is assembled into a roller shutter. During the operation, there shall be no inclination and parallel lifting. The height of the roller shutter shall not be greater than 1 / 300 of the opening.
          濟南鋁合金卷簾門門身裝配步驟:
          Assembly steps of Jinan aluminum alloy rolling shutter door body:
        濟南卷簾門廠
          1. 拆下軌道箱蓋,從兩側拆下鋁合金直軌,放入貼瓦門板兩側。
          1. Remove the track box cover, remove the aluminum alloy straight rail from both sides, and put it into both sides of the tile door panel.
          2. 電梯門板通過直軌進入身體,使直鐵路口與彎曲鐵路入口,將所有的門板塊推向渦輪機跟蹤,解決雙方的門與鏈板固定塊,并修復鋁合金直rails兩端的8毫米馬克螺絲。
          2. The elevator door plate enters the body through the straight rail, making the straight rail intersection and the curved railway entrance, pushing all the door plates to the turbine for tracking, solving the problem of fixing the door and chain plate on both sides, and repairing the 8mm mark screws at both ends of the aluminum alloy straight rails.
          3.放下門板,組裝電機,再將門板推入軌道,組裝張緊彈簧機構和雙鏈,供以后裝配。
          3. Lower the door panel, assemble the motor, push the door panel into the track, assemble the tension spring mechanism and double chain for later assembly.
          4,一直纏繞在高強度帶,保留1 - 2圈,皮帶和張力彈簧固定,注意固定,張力彈簧應該變直,然后用螺絲固定,電機的兩個鏈輪上的雙鏈內部螺絲收緊雙鏈,防止松動。
          4. The belt and tension spring shall be fixed. Pay attention to fixation. The tension spring shall be straightened and then fixed with screws. The double chain internal screws on the two sprockets of the motor shall tighten the double chain to prevent looseness.
          5. 用卷揚機或叉車將組裝好的門體手動豎立,保持軌道兩側靠近門兩側。如墻體用12顆膨脹螺絲固定在門體頂部,如鋼結構按甲方要求固定。
          5. Manually erect the assembled door body with a winch or forklift, and keep both sides of the track close to both sides of the door. If the wall is fixed on the top of the door body with 12 expansion screws, if the steel structure is fixed according to the requirements of Party A.
          6. 用紅外校平儀校準硬快校平和垂直度,用12膨脹螺絲固定軌道底部,用我公司準備的三角緊固件固定門體頂部。
          6. Calibrate the hard quick leveling and verticality with the infrared leveler, fix the bottom of the track with 12 expansion screws, and fix the top of the door body with the triangle fastener prepared by our company.
          為了避免濟南鋁合金卷簾門在后期使用中出現松動等問題,有關人員必須注意其安裝,按基本標準操作,以免帶來一系列的麻煩。
          In order to avoid the looseness and other problems in the later use of Jinan aluminum alloy roller shutter door, relevant personnel must pay attention to its installation and operate according to the basic standards, so as to avoid a series of troubles.

        推薦閱讀/ Recommended reading

        車庫門常見問題 Garage door FAQs 進行一些車庫門故障排除可以大大維護門的結構和功能。盡管有些問題您可能無法自行進行維修,但仍有一些

        車庫門電機保養知識介紹 2022-01-07
        有關車庫門的相關知識 2022-01-06
        車庫門保養你知道多少? 2021-12-24
        常見到的車庫門類型與特點 2021-12-23

        【本站圖片均由網站所有方提供,部分圖片來源于網絡,如無意中侵犯了某媒體或個人的知識產權,請來信或來電告之,本網站將立即刪除?!?/p>

        • 濟南九創門業有限公司
        乌克兰裸体美女AAAAAA片,久久精品人妻一区二区三区,女班长裸体扒开两腿让我桶动态图,欧美性爱A片